Our Location

We’re located in the Anderson Mill West area of Cedar Park, just north of Austin, TX.

Equipment

Control Equipment

image-left

Surprisingly, the brains of the entire show is a $60 Raspberry Pi 4. It runs a program called Falcon Player (FPP) that takes the playlist, sequences and effects for the show and sends that data to a Falcon F48 Differential Controller. The F48 further processes the data and talks to several Differential Smart Receivers distributed throughout the ‘stage’. Each Smart Receiver controls a small group of light strings.

The Lights

All the lights in the display are WS2811 RGB LED “pixel” nodes. With a few exceptions, like the Leaping Arches, all are bullet-style nodes. In the arches we use WS2811 LED strips.

There are over 5000 individual lights in the Halloween show and nearly 7000 for the Christmas show.

We sourced all of our pixel nodes, connectors and most of our cable from RGB-Man.com, and highly recommend them.

The Music

In addition to sending light data to the F48, the Raspberry Pi also handles playing the music. It is connected to a low-power FM transmitter, allowing visitors to listen in their cars or portable FM radios while watching the show without disturbing the neighbors.

The Software

For audio editing, processing and normalization, we use Audacity.

For developing the show sequences and effects, we use xLights.

To run the show, we use Falcon Player (FPP).

For scheduling and automation tasks, we use Home Assistant.

Features

House Outline

image-left

Most of the horizontal-running lights are attached to 1/2” PVC pipes, which are then attached under the soffits using PVC clips from HolidayCoro.

The vertical lights posed a bit more of a challenge, as much of the house is brick. So, I attached the lights to 3/4” EMT electical conduit with pipe hangers, and attached furniture levelers to the ends of the EMT. By adjusting the furniture levelers, I ‘pressure fit’ the EMT between the soffits and the ground. Finally, where I can, I secure the EMT to wood with pipe straps.

The overall solution makes it easy to assemble and disassemble with minimal permanent damage to the house.

Mega-Tree

image-left

The center pole of the Mega-Tree (Christmas show only) is a 10’ length of galvanized iron pipe.

At the bottom, the center pole is attached to some EMT conduit bent and joined into a semi-circle. The pipe and conduit are attached using connectors from MakerPipe (which, incidentally, are used generously throughout the whole display and highly recommended). This bottom structure is raised about 6” off the ground, and held in place with rebar driven through the EMT conduit/floor flange support legs and into the ground.

At the top, the center pole is connected to a custom tree-topper from Boscoyo Studios with a floor flange. J-hooks connect to the tree topper and stretch 24 strands of lights, each holding 60 lights, to the bottom where they are attached with bungee balls.

The Mega-Tree alone has 1440 lights.

Matrix

image-left

The Matrix is constructed of an 4’x8’ frame made of EMT electrical conduit, held together with MakerPipe connectors. To that frame we attached 1152 individual pixel nodes spaced 2” apart.

The mesh used to hold the lights in position was purchased from Boscoyo Studios.

Mini-Trees

image-left

The Mini-Trees (Christmas show only) are constructed of EMT conduit slipped over a piece of rebar driven into the ground. The lights are attached to standard Mega-Tree mounting strips and 1/2 of a ChromaPole set, both purchased from Boscoyo Studios. The strings of lights are connected to a ChromaPole plate at the top, and held to the ground with tent stakes. Each mini-tree has 108 individual lights.

Tombstones

image-left

The Tombstones (Halloween show only) are made of corrugated plastic and purchased from Boscoyo Studios. Each tombstone has 100 individual lights.

Leaping Arches

image-left

The 4 Leaping Arches are constructed of 2” HDPE tubing with LED strips inside. With some slight modifications, these were made following Matt Johnson’s Tutorial.

Singing Face/Spinner Prop

image-left

The large central ‘spinner’ over the garage door is a Hattitude Triune from Gilbert Engineering. This is one of our favorites due to its versatility. It can act as a high-density spinner to display designs and animation and also as a ‘singing face’ with several options.

Light Poles

image-left

The light poles on either side of the front door use Boscoyo ChromaPole top/bottom plates to connect 6x 30-light strings on a piece of EMT conduit slipped over a piece of rebar in the ground. Each pole has 180 lights and allows for doing numerous different effects.

Conclusion

When you come to see the show, please be respectful and don’t upset our neighbors. Click to review our Rules for Viewing.


Finally, some have commented after watching the videos that it looks as if I have some lights going out. Fortunately, it’s not the lights. I have a big Live Oak tree in front of the house and some smaller trees and shrubs in front of the porch that are obvious when you see it in person and much less distracting than in the videos.

image-left

If you’re thinking about, or in the middle of, building your own display and want more details about how I did something, or why I did it that way, feel free to email me at chgo2022@opayq.com.